TORNADO UFS TECHNIQUESTips and Tricks On Using Tornado UFS3 Nokia
In the case of 1st Boot Err or Bad Resp DCT3
* Damage like this is common because it is not terhubungnya between the Box with a mobile phone
* Check the flasher cable is used, because it is possible there is a broken line
* If the cable is in good condition, there may be some damage to the software UFS3
* Reinstall the program with data that is still good
In Case of Contact Service
* Damage such as this usually occurs because of damage data
* Perform data removal process with Erase FLASH
* Then do the flashing with data that is still good
* Put a tick in the UI Options and click the Settings UI
* If there is damage to the IMEI data, do the Rebuild IMEI and repeat the process UI Settings
* If the damage due to hardware, there are some IC that causes it, but cases like this simply by replacing the IC or IC Audio COBBA
If sata or Erasing Flashing process, the process stalled
* Perform data removal process with Erase FLASH
* Then do the flashing with data that is still good
* Put a tick in the UI Options and click the Settings UI
* If there is damage to the IMEI data, do the Rebuild IMEI and repeat the process UI Settings
* If the damage due to hardware, there are some IC that causes it, but cases like this simply by replacing the IC or IC Audio COBBA
If sata or Erasing Flashing process, the process stalled
* Check the flasher cable, because it shows the breakdown of the relationship between cellular telephone with Flasher Box
* Repeat process with reducing speed Speed Flasher
* If it still stops at the same position repeatedly, it is possible to crash the Flash IC
In the case of failed Phone blimking contact retailers or on the phone type WD2
In the case of failed Phone blimking contact retailers or on the phone type WD2
* Make sure the phone is connected well with UFS3 Tornado Box
* Run the program UFS3 Tornado for Nokia mobile phone and select the type of WD2
* Choose a type mobile phone that is being repaired
* Click the Connect button to liaison between the Box UFS3 Tornado with Computers
* Click the button Check to make sure the phone had been connected "Boot Okay"
* In the UI Settings column select Normal, wait until the Normal Mode OK
* After appearing on the screen Normal Mode Ok continue by pressing the Format User Area
* Finish Process
Practical Solutions Contact retailer or Blimking on Nokia 6600 mobile phone
* Run the program UFS3 Tornado for Nokia mobile phone and select the type of WD2
* Choose a type mobile phone that is being repaired
* Click the Connect button to liaison between the Box UFS3 Tornado with Computers
* Click the button Check to make sure the phone had been connected "Boot Okay"
* In the UI Settings column select Normal, wait until the Normal Mode OK
* After appearing on the screen Normal Mode Ok continue by pressing the Format User Area
* Finish Process
Practical Solutions Contact retailer or Blimking on Nokia 6600 mobile phone
* If, while Flashing occurs Erase error
* Click Erase FLASH with the provisions of the Start Address and End Address 027FFFFF 02000000
* If there Erase Flash Error then have to replace the flash IC No. 2, from 4 existing IC
* If the process is successful, but when power was still at the Contact retailer
* Remove and replace battry again, then press the Call button on Hanphone or green button +
* + number 3 on the mobile phone by simply pressing together, without using the sim card
* After the above steps have been made, then the phone will do the formatting
* After formatting, the phone is ready to use
In the case of Simcard Rejected or Simcard rejected a common cell phone types and DCT-4 WD2
* Click Erase FLASH with the provisions of the Start Address and End Address 027FFFFF 02000000
* If there Erase Flash Error then have to replace the flash IC No. 2, from 4 existing IC
* If the process is successful, but when power was still at the Contact retailer
* Remove and replace battry again, then press the Call button on Hanphone or green button +
* + number 3 on the mobile phone by simply pressing together, without using the sim card
* After the above steps have been made, then the phone will do the formatting
* After formatting, the phone is ready to use
In the case of Simcard Rejected or Simcard rejected a common cell phone types and DCT-4 WD2
* Make sure the phone is connected well with UFS3 Tornado Box
* Run the program UFS3 Tornado for Nokia mobile phone and select the type or DCT-4 WD2
* Choose a type mobile phone that is being repaired
* Click the Connect button to liaison between the Box UFS3 Tornado with Computers
* Click the button Check to make sure the phone had been connected "Boot Okay"
* In the UI Settings column select Normal, wait until the Normal Mode Ok
* After appearing on the screen Normal Mode Ok proceed by giving the Init Simlocks checklist contained in the columns UI Options
* Then click the Settings UI to appear on the screen Ok Init Simlock
In the case of No Charging and No Signal On Phone type and DCT-4 WD2
* Run the program UFS3 Tornado for Nokia mobile phone and select the type or DCT-4 WD2
* Choose a type mobile phone that is being repaired
* Click the Connect button to liaison between the Box UFS3 Tornado with Computers
* Click the button Check to make sure the phone had been connected "Boot Okay"
* In the UI Settings column select Normal, wait until the Normal Mode Ok
* After appearing on the screen Normal Mode Ok proceed by giving the Init Simlocks checklist contained in the columns UI Options
* Then click the Settings UI to appear on the screen Ok Init Simlock
In the case of No Charging and No Signal On Phone type and DCT-4 WD2
* Make sure the phone is connected well with UFS3 Tornado Box
* Run the program UFS3 Tornado for Nokia mobile phone and select the type or DCT-4 WD2
* Choose a type mobile phone that is being repaired
* Click the Connect button to liaison between the Box UFS3 Tornado with Computers
* Click the button Check to make sure the phone had been connected "Boot Ok"
* In the UI Settings column select Normal, wait until the Normal Mode Ok
* Click the button write pm (Wr PM), only 1 time with a provision has been saved PM file from each phone in the directory (C: \ Program files \ Nokia \ Phoenix \ Products)
* Wait until the process is complete
To overcome the problem Phone Locks on the phone type Nokia
* Run the program UFS3 Tornado for Nokia mobile phone and select the type or DCT-4 WD2
* Choose a type mobile phone that is being repaired
* Click the Connect button to liaison between the Box UFS3 Tornado with Computers
* Click the button Check to make sure the phone had been connected "Boot Ok"
* In the UI Settings column select Normal, wait until the Normal Mode Ok
* Click the button write pm (Wr PM), only 1 time with a provision has been saved PM file from each phone in the directory (C: \ Program files \ Nokia \ Phoenix \ Products)
* Wait until the process is complete
To overcome the problem Phone Locks on the phone type Nokia
* Make sure the phone is connected well with UFS3 Tornado Box
* Run the program for Nokia phones UFS3 Tornado
* Choose a type mobile phone that is locked or the phone lock
* Click the Connect button to liaison between the Box UFS3 Tornado with Computers
* Click the button Check to make sure the phone had been connected "Boot Okay"
* Put a tick in the Full Factory Devaults contained in the columns UI Options
* Then click the Settings UI to appear on the screen Full Factory Devaults Okay
Tips and Tricks Using UFS3 Tornado On Sony Ericsson phones
Practical Ways Sony Ericsson Flashing
* Run the program for Nokia phones UFS3 Tornado
* Choose a type mobile phone that is locked or the phone lock
* Click the Connect button to liaison between the Box UFS3 Tornado with Computers
* Click the button Check to make sure the phone had been connected "Boot Okay"
* Put a tick in the Full Factory Devaults contained in the columns UI Options
* Then click the Settings UI to appear on the screen Full Factory Devaults Okay
Tips and Tricks Using UFS3 Tornado On Sony Ericsson phones
Practical Ways Sony Ericsson Flashing
* Make sure the phone is connected well with UFS3 Tornado Box
* Click the Connect button located on the top left of the program
* Battery should not be installed first before pressing the ON button, after pressing the button on your new pair of batteries, wait until all information completely legible phone
* Choose a type mobile phone that will be flashed and also select the appropriate data type phones that do
* Click the Flash button or Flash MCU Mod Lang or Flash or Flash GDFS or depending on the cell phone under construction
How to unlock Z200 Unlock
* Click the Connect button located on the top left of the program
* Battery should not be installed first before pressing the ON button, after pressing the button on your new pair of batteries, wait until all information completely legible phone
* Choose a type mobile phone that will be flashed and also select the appropriate data type phones that do
* Click the Flash button or Flash MCU Mod Lang or Flash or Flash GDFS or depending on the cell phone under construction
How to unlock Z200 Unlock
* In this case we can start by pressing the Init Locks on UFS3 Tornado
* Followed by mereflash re-file "Z200_cust_std.bis by pressing the flash button on the program Cust UFS3 Tornado or by setting up the scenario to choose Unlock column by pressing the Go button.
Flashing Sony Ericsson Z200 Series Type ATRZ
* Followed by mereflash re-file "Z200_cust_std.bis by pressing the flash button on the program Cust UFS3 Tornado or by setting up the scenario to choose Unlock column by pressing the Go button.
Flashing Sony Ericsson Z200 Series Type ATRZ
* Enter the file or data such as language and 200_126734_r6c_fix3 200_126734_r6c_con3.bis on in part2 part1
* Connect the mobile phone with flasher box and press the Go button
* Wait until the finish, to end press the Stop button and the phone ready to be released
Flashing Sony Ericsson T610 series RTP Type
* Connect the mobile phone with flasher box and press the Go button
* Wait until the finish, to end press the Stop button and the phone ready to be released
Flashing Sony Ericsson T610 series RTP Type
* Enter the MCU file such as modem files T610_132233_r4c003_Emea6.bis and T610_132233_r4c003_modem.bih
* Select the column scenario MCU + Modem
* Connect the mobile phone and press the Go button, wait until the process is complete
* Click Stop to release mobile phone
Tips and Tricks Using UFS3 Tornado on Samsung phone
* Select the column scenario MCU + Modem
* Connect the mobile phone and press the Go button, wait until the process is complete
* Click Stop to release mobile phone
Tips and Tricks Using UFS3 Tornado on Samsung phone
* Make sure the phone is connected well with UFS3 Tornado Box
* Click the Connect button located on the top left of the program
* Choose a type mobile phone that will be flashed and also select the appropriate data type phones that do
* Enter the file flasher according to the type of phone that worked
* Remove the battery (flash without battery)
* Press the 'Write Flash' contained in the program UFS3 Tornado and continue by pressing the 'on' on the phone not to flame
* Wait until flash process is complete
* To type a specific phone or cell phone batteries remain attached long time in the flash
* Click the Connect button located on the top left of the program
* Choose a type mobile phone that will be flashed and also select the appropriate data type phones that do
* Enter the file flasher according to the type of phone that worked
* Remove the battery (flash without battery)
* Press the 'Write Flash' contained in the program UFS3 Tornado and continue by pressing the 'on' on the phone not to flame
* Wait until flash process is complete
* To type a specific phone or cell phone batteries remain attached long time in the flash
{ 0 comments... Views All / Send Comment! }
Post a Comment